(mule-keymap, mule-menu-keymap)

[gnu-emacs] / INSTALL.CVS

diff --git a/INSTALL.CVS b/INSTALL.CVS
index b8c42de27d59077c788f279ac28a5534be6acc5b..aee016f28d38a3ee7ee30fb7925dfd344f6a52c8 100644 (file)
--- a/INSTALL.CVS
+++ b/INSTALL.CVS
@@ -1,56 +1,47 @@
-Copyright (C) 2002, 2003, 2004, 2005, 2006, 2007, 2008
+Copyright (C) 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009

   Free Software Foundation, Inc.
 See the end of the file for license conditions.
 
 
              Building and Installing Emacs from CVS
 
   Free Software Foundation, Inc.
 See the end of the file for license conditions.
 
 
              Building and Installing Emacs from CVS
 

+If this is the first time you go through it, you'll need to configure
+before bootstrapping:
+
+  $ ./configure
+

 Some of the files that are included in the Emacs tarball, such as
 byte-compiled Lisp files, are not stored in the CVS repository.
 Therefore, to build from CVS you must run "make bootstrap"
 instead of just "make":
 
 Some of the files that are included in the Emacs tarball, such as
 byte-compiled Lisp files, are not stored in the CVS repository.
 Therefore, to build from CVS you must run "make bootstrap"
 instead of just "make":
 

-  $ ./configure
+  $ cvs update -dP

   $ make bootstrap
 
   $ make bootstrap
 

-The bootstrap process makes sure all necessary files are rebuilt
-before it builds the final Emacs binary.
-
-If 'make bootstrap' fails, it may be necessary to do 'make maintainer-clean'
-followed by configure before trying it again.  (Occasionally the loaddefs.el
-file gets into a bad state due to changes in the Lisp libraries; this procedure
-forces it to be regenerated.)
-

 Normally, it is not necessary to use "make bootstrap" after every CVS
 Normally, it is not necessary to use "make bootstrap" after every CVS

-update.  Unless there are problems, we suggest using the following
-alternative procedure after you have done "make bootstrap" at least
-once:
+update.  "make" should work in 90% of the cases and be much quicker.

 
 

-  $ ./configure
-  $ make
-  $ cd lisp
-  $ make recompile EMACS=../src/emacs
-  $ cd ..

   $ make
 
 (If you want to install the Emacs binary, type "make install" instead
 of "make" in the last command.)
 
   $ make
 
 (If you want to install the Emacs binary, type "make install" instead
 of "make" in the last command.)
 

-Occasionally the file "lisp/loaddefs.el" (and similar *-loaddefs.el
-files in some subdirectories of lisp/, e.g. mh-e/ and calendar/) will
-need to be updated to reflect new autoloaded functions.  If you see
-errors (rather than warnings) about undefined lisp functions during
-compilation, that may be the reason.  Another symptom may be an error
-saying that "loaddefs.el" could not be found; this is due to a change
-in the way loaddefs.el was handled in CVS, and should only happen
-once, for users that are updating old CVS trees.  Finally, sometimes
-there can be build failures related to *loaddefs.el.  In that case,
-delete them before following the instructions below to update them.
+Occasionally the file "lisp/loaddefs.el" (and similar automatically
+generated files, such as esh-groups.el, and *-loaddefs.el in some
+subdirectories of lisp/, e.g. mh-e/ and calendar/) will need to be
+updated to reflect new autoloaded functions.  If you see errors (rather
+than warnings) about undefined lisp functions during compilation, that
+may be the reason.  Another symptom may be an error saying that
+"loaddefs.el" could not be found; this is due to a change in the way
+loaddefs.el was handled in CVS, and should only happen once, for users
+that are updating old CVS trees.  Finally, sometimes there can be build
+failures related to *loaddefs.el (e.g. "required feature `esh-groups'
+was not provided").  In that case, follow the instructions below.

 
 To update loaddefs.el (and similar files), do:
 
   $ cd lisp
 
 To update loaddefs.el (and similar files), do:
 
   $ cd lisp

-  $ make autoloads EMACS=../src/emacs
+  $ make autoloads

 
 If either of the above partial procedures fails, try "make bootstrap".
 
 
 If either of the above partial procedures fails, try "make bootstrap".
 


@@ -64,15 +55,19 @@ method.
 Users of non-Posix systems (MS-Windows etc.) should run the
 platform-specific configuration scripts (nt/configure.bat, config.bat,
 etc.) before "make bootstrap" or "make"; the rest of the procedure is
 Users of non-Posix systems (MS-Windows etc.) should run the
 platform-specific configuration scripts (nt/configure.bat, config.bat,
 etc.) before "make bootstrap" or "make"; the rest of the procedure is

-applicable to those systems as well, except that the value of the
-EMACS variable on the Make command line might be different, e.g.,
-../bin/emacs.exe or some such.
+applicable to those systems as well.

 
 Questions, requests, and bug reports about the CVS versions of Emacs
 should be sent to emacs-pretest-bug@gnu.org rather than gnu.emacs.help
 or gnu.emacs.bug.  Ideally, use M-x report-emacs-bug RET which will
 send it to the proper place.
 
 
 Questions, requests, and bug reports about the CVS versions of Emacs
 should be sent to emacs-pretest-bug@gnu.org rather than gnu.emacs.help
 or gnu.emacs.bug.  Ideally, use M-x report-emacs-bug RET which will
 send it to the proper place.
 

+Because the CVS version of Emacs is a work in progress, it will
+sometimes fail to build.  Please wait a day or so (and check the bug
+and development mailing list archives) before reporting such problems.
+In most cases, the problem is known about and is just waiting for
+someone to fix it.
+

 
 Note on using SSH to access the CVS repository from inside Emacs
 ----------------------------------------------------------------
 
 Note on using SSH to access the CVS repository from inside Emacs
 ----------------------------------------------------------------