# Hide user interface elements for personal preference or to increase
# security:
# banner - the rEFInd title banner
-# label - text label in the menu
+# label - boot option text label in the menu
# singleuser - remove the submenu options to boot Mac OS X in single-user
# or verbose modes; affects ONLY MacOS X
# hwtest - the submenu option to run Apple's hardware test
# arrows - scroll arrows on the OS selection tag line
+# hints - brief command summary in the menu
+# editor - the options editor (+, F2, or Insert on boot options menu)
# all - all of the above
+# Default is none of these (all elements active)
#
#hideui singleuser
#hideui all
#selection_small selection-small.bmp
# Use text mode only. When enabled, this option forces rEFInd into text mode.
+# Passing this option a "0" value causes graphics mode to be used. Pasing
+# it no value or any non-0 value causes text mode to be used.
+# Default is to use graphics mode.
#
#textonly
-# Set the screen's video resolution. Pass this option two values,
-# corresponding to the X and Y resolutions. Note that not all resolutions
-# are supported. On UEFI systems, passing an incorrect value results in a
-# message being shown on the screen to that effect, along with a list of
-# supported modes. On EFI 1.x systems (e.g., Macintoshes), setting an
-# incorrect mode silently fails. On both types of systems, setting an
-# incorrect resolution results in the default resolution being used.
-# A resolution of 1024x768 usually works, but higher values often don't.
+# Set the EFI text mode to be used for textual displays. This option
+# takes a single digit that refers to a mode number. The default is 0
+# (80x25), 1 is sometimes 80x50, and higher numbers are system-specific
+# modes. If you specify an invalid mode, rEFInd pauses during boot to
+# inform you of valid modes.
+# CAUTION: On VirtualBox, and perhaps on some real computers, specifying
+# a text mode and uncommenting the "textonly" option while NOT specifying
+# a resolution can result in an unusable display in the booted OS.
+# Default is 0
+#
+#textmode 2
+
+# Set the screen's video resolution. Pass this option either:
+# * two values, corresponding to the X and Y resolutions
+# * one value, corresponding to a GOP (UEFI) video mode
+# Note that not all resolutions are supported. On UEFI systems, passing
+# an incorrect value results in a message being shown on the screen to
+# that effect, along with a list of supported modes. On EFI 1.x systems
+# (e.g., Macintoshes), setting an incorrect mode silently fails. On both
+# types of systems, setting an incorrect resolution results in the default
+# resolution being used. A resolution of 1024x768 usually works, but higher
+# values often don't.
# Default is "0 0" (use the system default resolution, usually 800x600).
#
#resolution 1024 768
+#resolution 3
# Launch specified OSes in graphics mode. By default, rEFInd switches
# to text mode and displays basic pre-launch information when launching
# reboot - a tag to reboot the computer
# Default is shell,apple_recovery,mok_tool,about,shutdown,reboot
#
-#showtools shell, about, reboot
+#showtools shell, mok_tool, about, reboot, exit
# Directories in which to search for EFI drivers. These drivers can
# provide filesystem support, give access to hard disks on plug-in
# want to give a kernel a custom icon by placing an icon with the kernel's
# filename but a ".icns" extension in the same directory as the kernel, this
# option will cause the icon file to show up as a non-functional loader tag.
+# Passing this option a "0" value causes kernels without ".efi" extensions
+# to NOT be scanned; passing it alone or with any other value causes all
+# kernels to be scanned.
# Default is to NOT scan for kernels without ".efi" extensions.
#
-#scan_all_linux_kernels
+scan_all_linux_kernels
# Set the maximum number of tags that can be displayed on the screen at
# any time. If more loaders are discovered than this value, rEFInd shows
#
#default_selection 1
+# Include a secondary configuration file within this one. This secondary
+# file is loaded as if its options appeared at the point of the "include"
+# token itself, so if you want to override a setting in the main file,
+# the secondary file must be referenced AFTER the setting you want to
+# override. Note that the secondary file may NOT load a tertiary file.
+#
+#include manual.conf
+
# Sample manual configuration stanzas. Each begins with the "menuentry"
# keyword followed by a name that's to appear in the menu (use quotes
# if you want the name to contain a space) and an open curly brace